The limescale marks on your shower door are what the water leaves behind. When a drop dries, the water evaporates, but the minerals that were dissolved in it stay on the glass. Drop by drop, they build up into a white film. The best protection is to remove the water right after the shower, before it has time to dry.
Why does limescale form in the shower?
Tap water contains calcium and magnesium. According to Svenskt Vatten (the Swedish water industry association), it is the amount of these two that determines how hard the water is. The Swedish Food Agency (Livsmedelsverket) says that hard water can cause deposits in pipes and fittings, especially when the water is heated. In the shower you have both hot water and plenty of drops drying onto glass, tiles and faucets.
Soft water doesn’t protect completely. Stockholm’s tap water counts as soft, 4–6 °dH, and still leaves a white limescale deposit when boiled, according to Stockholm Vatten och Avfall, the city’s water and waste utility. With harder water, the marks come faster. Limescale is harmless. Livsmedelsverket says that hard water is fine to drink and cook with.
How hard is the water where I live?
Your water supplier or municipality publishes the hardness on its website, usually in German degrees of hardness (°dH). Svenskt Vatten uses the classification below and points out that the limits are not absolute. The last column is our interpretation for the shower.
| Hardness | °dH | What it means for the shower |
|---|---|---|
| Very soft | 0–2 | Little limescale per drop, but it builds up if the water is left to dry day after day |
| Soft | 2–5 | A thin film over time, clearest on dark and shiny surfaces |
| Medium hard | 5–10 | Visible marks if you don’t dry off |
| Hard | 10–20 | The marks come quickly, so dry off after every shower |
| Very hard | over 20 | A lot of limescale per drop, so drying off makes the biggest difference here |
Livsmedelsverket’s guideline value for hardness in drinking water is 15 °dH. Above that, the water is classed as fit to drink “with remarks”, but it is not harmful to health.
Squeegee or towel – what works best against limescale?
Both work, as long as the water goes. A manufacturer’s care leaflet for shower doors describes the most effective and most environmentally friendly way to keep the shower clean. You pull a rubber squeegee across the glass or wipe it down with a soft cloth after every shower. Svedbergs, a Swedish maker of bathroom fittings, gives the same advice for faucets and says you avoid limescale marks if you wipe with a soft cloth after each use.
A squeegee is quick on large, flat glass surfaces. Water still stays where it can’t reach: along the bottom edge, in the corners, around the frames and hinges, on the faucet and on textured tiles. There you need a cloth or towel.
| Method | Good for | Weaker on |
|---|---|---|
| Rubber squeegee | Large, flat glass surfaces | Corners, edges, frames, faucets and textured tiles |
| Microfiber cloth | Faucets, mirrors and smaller surfaces | Has to be wrung out often on a whole shower door |
| Bathroom drying towel | Glass, edges, frames and faucets in one go | Has to be hung up to dry and washed |
| Ordinary terry cloth towel | Already at home | Gets wet fast and can leave lint on the glass |
| Cold water or a fan | Soap residue and moisture in the room | The limescale in the drops stays behind |
We sell a drying towel for exactly this, Shiny Wipes. It has a curly side that soaks up the water and a smooth side that polishes, and comes in M, 12 × 16 in (30 × 40 cm), and XL, 16 × 24 in (40 × 60 cm). You don’t need to buy anything to get started. A clean microfiber cloth or an old towel does the same job on smaller surfaces. If you already have a squeegee, you can squeegee the glass first and do edges and faucets with the cloth afterwards.
Does cold water or ventilation help against limescale?
Cold water rinses away soap and shampoo, and ventilation deals with the moisture. Neither removes the limescale in the drops. The cold water comes from the same pipe as the hot and contains the same calcium, so the drops leave marks when they dry.
With the exhaust fan on and the door open, the drops on the glass dry faster, and the limescale stays behind just the same. By all means rinse and ventilate, but dry off as well.
How do you dry shower glass without streaks?
Streaks often come from the cloth being too wet. A saturated cloth leaves a thin film of water, and it dries into the same white film you wanted to avoid. Wring out the cloth as soon as it feels heavy. If you have both a squeegee and a cloth, let the squeegee take most of the water and use the cloth for edges and the final wipe. Also wipe the squeegee blade between strokes, otherwise you drag the water back across. For a shine on the faucet, polish it with a dry part of the cloth.
Does a coating on the glass protect against limescale?
Some shower doors are sold with a coating that makes water run off more easily. Fewer drops are left, but the ones that remain dry in the same way. Dry off anyway. Also take care of the coating. The manufacturer’s leaflet for shower doors warns that sponges and abrasive cleaning pastes can scratch glass and metal, and asks you to check that the cleaning product suits your particular surface.
How often should you clean the shower door?
If you dry off after every shower, a simple clean about once a week is enough. INR recommends cleaning faucets weekly with a soft cloth and a mild soap solution or pH-neutral cleaner, followed by rinsing and drying. The glass can take the same gentle cleaning. If a white film has formed anyway, you need an acid, such as household vinegar. How to do it without damaging grout and faucets is covered in Remove limescale from your shower door. The same technique for shiny, streak-free glass is in Cleaning windows without streaks. You’ll find more cleaning things under Cleaning.
Common mistakes
- Only drying the glass. Faucets, frames and tiles near the floor get drops too.
- Saving the cleaning for the weekend. By then a week’s worth of drops has already dried on.
- Leaving the squeegee outside the shower. Hang it on a hook inside the shower, where you see it when you turn off the water.
- Using an abrasive sponge on the marks. It can scratch glass and metal.
- Fabric softener in the wash. Fabric softener coats the fibers so the cloth absorbs less.
- Cold water as the only protection. It rinses away soap but not limescale.
Sources
- Svenskt Vatten: Facts about drinking water
- Livsmedelsverket: Interpreting your water analysis result
- Stockholm Vatten och Avfall: Questions and answers about tap water
- Care advice for shower doors (manufacturer’s leaflet, published via HSB)
- Svedbergs: Faucets, product and care description (PDF)
- INR: Care advice for faucets (PDF)






